eips-bfr Version Sacha

APPLICATIONS
CONTACT:
Email: m[email protected]
Tel.: [phone]
www.adas.fr
• Aircraft test
• Airborne cargo test
• Armored vehicle test
♦ Continuous input 28 V DC,
20 V - 36 V / 5A - 3A
♦ Output power 80 W to 25°C /
60 W to 85°C
♦ Outputs :
− +/- 15 V/600 mA
− +/- 6 V/2 A
− + 5 V/5 A
− + 3,3 V/3,5 A
− + 2,5 V/2 A
♦ ALFAIL and SYSRESET
generation
♦ Connectors:
− LEMO + HD in FAV
− AMP Minibox in FdP
♦ Visualization DELs:
− Control Σ power supplies
− BUS exchange
♦ Various protections
♦ Severe environments
EIPS board has been developed to both condition and
acquire analog and digital isochronous parameters for
SACHA and SARI systems. The board provides the power
supply necessary to the different boards in the rugged
systems.
The board provides 60 W power from the 28V network
with a wide input range.
EIPS board also includes ‘tools’ to ease both wiring and
daily use of SACHA and SARI systems.
POWER SUPPLY BOARD
EIPS
SPECIFICATIONS*
INPUT
Nominal voltage 28 V DC / 3,5A max
Voltage of input range 20 V à 36 V
Protections
Reverse voltage allowed - 40 V DC
Temporary overload voltage +80 V DC
- On current 6A max with automatic RESTART and
power limitation (0,1 % duty cycle)
Capacity ≥ 80 % of nominal power
ISOLATION
Input / Chassis 100 V ac / 10 MΩ
Input/ output 100 V ac / 10 MΩ
OUTPUT
Available power 80 W à 25°C / 60 W à 85°C
Voltage/Current
+ 15 V / 600 mA ; - 15 V / 600 mA
+ 6 V / 2,5 A ; - 6 V / 2,5 A
+ 5 V / 5A ; + 3,3 V / 3,5 A ; + 2,5 V / 2A
Temperature coeff. ± 0,04 % / °C
Noise 75 mVpp Band DC - 10 MHz
Regulation ± 0,5 % max, Full load
Protection Against short circuit

SPECIFICATIONS*
WWW. ADAS.FR
EIPS - POWER SUPPLY BOARD
MAIN FUNCTIONS
EPROM identification Reading characteristics using I2C bus (type, serial NO,…)
SYSRESET Transmitting a reset signal when powering (t = 0,6 second)
ALFAIL Detection of primary voltage lost via optocouplers
Failure detection Control of whole voltage available
IRIG B Analog input of dating signal in conformance with IRIG B standard
Discrete output 3 discrete « TTL » active at high state ( I out ≤ 10mA ) DØ ; D1 ; D2
Discrete input 3 Discrete « TTL » active at low state ( pull up at internal + 5V) LØ ; L1 ; L2
NB : for discrete I/O, the mass reference is EM (internal electrical mass of the enclosure)
CAN Bus CAN interface on request, in place of DIGITIME (H.DATE I/O )
H.DATE I/O Differential link of time transmission (IRIG B NUMERIQUE)
PCM links Two bi-directional Ethernet links
Synchro Synchronization between I/O enclosures (master/slave)
PPS TTL output pulse active at state 1
Rising edge and image of reference second
Ethernet Ethernet link towards board
CPU via FDP
DELS
4 DELS in front panel
ok Ʃ Alim. : green = ok
pps emit. : green = flash to second
Synchro. : green = system sets time
record : green = recording
PHYSICAL DESCRIPTION
Size (H x W x D) 77 x 110 x 12 mm
Front 88 x 20 mm
Weight
TBD
CONNECTIVITY
Backplane AMP 501 MINIBOX 80 pts
Front Panel Auxiliary: HDA 26 S Ethernet: LEMO - EXG - 0B – 304
Power: LEMO - EXG - 0B - 303
ENVIRONMENT
Storage temperature - 55 + 125°C
Operating temperature - 40 + 75°C
Specifications - 10 + 60°C
Relative humidity 90 % non condensing
Sinusoidal vibrations 20 à 2.000 Hz - 5g
Random vibrations 10 à 2.000 Hz - 6g eff
Shocks 100 g/6 ms
Pressure 25 à 1.100 mbar
Electromagnetic Environment MIL STD 461 et GAM EG13
EUROPEAN STANDARDS
EMC - EN 61326 - EN 55011 Class A CE Compliance
ROHS - 2002/95/EC
*Specifications given for 25°C

WWW. ADAS.FR
EIPS - POWER SUPPLY BOARD
EIPS FRONT PANEL
ETHERNET
POWER
LED SIGNAL
1 ƩAL
2 ACQ
3 SYSTEME
4 PPS
DESCRIPTION
ORANGE : Power supply. failure
GREEN : Ʃ Power suppy OK
Green flashes for ongoing acquisitions
GREEN : system operaonal
Flashes on second PPS issue
PIN SIGNAL
1 TX (+)
2 TX (-)
2 RX (+)
4 RX (-)
PIN SIGNAL
1 + 28V
2 R 28V
3 MM
PIN 9 8 7 6 5 4 3 2 1
SIGNAL DATA
B (-)
CLK
B (-)
DATA
A (-)
CLK
A (-) SYNC (-) L.SYST L.PCM L.OK AL VALP
PIN 18 17 16 15 14 13 12 11 10
SIGNAL DATA
B (+)
CLK
B (+)
DATA
A (+)
CLK
A (+) SYNC (+) D.IN2 D.IN1 D.IN0 M/A ALIM
PIN 26 25 24 23 22 21 20 19
SIGNAL ME H.DATE
(+) H.DATE(-) ME PPS (OUT)
IRIG B
(IN) ME R28V
EIPS FRONT PANEL
CONTROL AND PCM CONNECTOR

Specifications are subject to change. Please, verify the latest specifications prior order.
Version : 2.0 — Edion : June 2016
EIPS - POWER SUPPLY BOARD
ORDERING INFORMATION
EIPS Power supply board
BROCHE SIGNAL DESCRIPTION
1 VALP OR between 28V supply and internal (when used)
10 M/A ALIM POWER ON of system : active when low : must be wired at R28V.
19 R28V External 28V return
11 D.IN0
RESET/
System control
ENR/ Active when low (pull up at +5V)
Reference : ME
USER/ (M/S)
12 D.IN1
13 D.IN2
2 L.OK AL
System status
Active when high (+5V/10mA)
Reference ME
3 L.PCM
4 L. SYST
5 SYNC (-) RS485 signal for inter-system-synchronisation (Facq)
Input or Output (software programmable
Reference ME
14 SYNC (+)
21 IRIG B IRIG B analog signal, input
22 PPS Output Pulse active when ″1″ (5V/10mA)
6 CLK A (-)
PCM A (input or output)
(DATA + clock)
RS485
Reference ME
7 DATA A (-)
15 CLK A (+)
16 DATA A (+)
8 CLK B (-)
PCM B (input or output)
(DATA + clock)
RS485
Reference ME
9 DATA B (-)
17 CLK B (+)
18 DATA B (+)
24 H.DATE (-)
Digital IRIG B IN/OUT (D/M/S)
25 H.DATE (+)
20
ME ME : internal electrical reference of system
23
26

EIPS – Rev. B – Edition 1 – 28/33
1
TRACEABILITY FORM
DOCUMENT FOLLOW-UP
Title:
Titre : EIPS
Documentation française
Rév. B - Edition 1 – 28/33
Revised
A
pproved
Written
by
by
by D. PIMONT
D. PIMONT
Ph. DUTIN
on
on
on
28/33
28/33
28/33
Visa
Visa
Visa
Warning: Unless otherwise stated, this revision
overwrites the previous one which must be
destroyed, along with any copies given to your
collaborators.
Avertissement : En l’absence d’indication contraire, cette nouvelle édition
annule et remplace l’édition précédente qui doit être détruite, ainsi que les
copies faites à vos collaborateurs.
Table of the modifications
Table des évolutions (mots clés) Page n°
DSQ - 4.5.a - Indice G - 28/02 T.S.V.P.