ba2489566 01 en tapcon260

Voltage Regulator
TAPCON® 260
Operating Instructions
2489566/01 EN

© All rights reserved by Maschinenfabrik Reinhausen
Dissemination and reproduction of this document and use and disclosure of its content are strictly prohibited
unless expressly permitted.
Infringements will result in liability for compensation. All rights reserved in the event of the granting of patents,
utility models or designs.
The product may have been altered since this document was published.
We reserve the right to change the technical data, design and scope of supply.
Generally the information provided and agreements made when processing the individual quotations and orders
are binding.
The original operating instructions were written in German.

Table of contents
Maschinenfabrik Reinhausen 2014 32489566/01 EN TAPCON® 260
Table of contents
1Introduction ......................................................................................................................... 9
1.1 Manufacturer ....................................................................................................................................... 9
1.2 Subject to change without notice......................................................................................................... 9
1.3 Completeness...................................................................................................................................... 9
1.4 Supporting documents......................................................................................................................... 9
1.5 Safekeeping....................................................................................................................................... 10
1.6 Notation conventions ......................................................................................................................... 10
1.6.1 Hazard communication system ........................................................................................................................... 10
1.6.2 Information system .............................................................................................................................................. 11
1.6.3 Typographic conventions .................................................................................................................................... 11
2Safety ................................................................................................................................. 12
2.1 General safety information ................................................................................................................ 12
2.2 Appropriate use ................................................................................................................................. 12
2.3 Inappropriate use............................................................................................................................... 12
2.4 Personnel qualification ...................................................................................................................... 13
2.5 Operator's duty of care ...................................................................................................................... 13
3Product description .......................................................................................................... 14
3.1 Scope of delivery ............................................................................................................................... 14
3.2 Function description of the voltage regulation ................................................................................... 14
3.3 Performance features ........................................................................................................................ 15
3.4 Operating modes ............................................................................................................................... 16
3.5 Hardware ........................................................................................................................................... 17
3.5.1 Name plate .......................................................................................................................................................... 17
3.5.2 Operating controls ............................................................................................................................................... 18
3.5.3 Display elements ................................................................................................................................................. 20
3.5.4 Serial interface .................................................................................................................................................... 21
3.5.5 Assemblies .......................................................................................................................................................... 21
4Packaging, transport and storage................................................................................... 30
4.1 Packaging.......................................................................................................................................... 30
4.1.1 Suitability, structure and production ................................................................................................................... 30
4.1.2 Markings.............................................................................................................................................................. 30
4.2 Transportation, receipt and handling of shipments............................................................................ 30

Table of contents
Maschinenfabrik Reinhausen 20144 2489566/01 ENTAPCON® 260
4.3 Storage of shipments......................................................................................................................... 31
5Mounting ............................................................................................................................ 32
5.1 Preparation ........................................................................................................................................ 32
5.2 Mounting device ................................................................................................................................ 32
5.3 Connecting device ............................................................................................................................. 33
5.3.1 Cable recommendation ....................................................................................................................................... 33
5.3.2 Information about laying fiber-optic cable............................................................................................................ 35
5.3.3 Electromagnetic compatibility.............................................................................................................................. 35
5.3.4 Connecting cables to the system periphery ........................................................................................................ 39
5.3.5 Wiring device....................................................................................................................................................... 39
5.3.6 Checking functional reliability .............................................................................................................................. 40
6Commissioning ................................................................................................................. 41
6.1 Setting the display contrast ............................................................................................................... 41
6.2 Setting parameters ............................................................................................................................ 41
6.2.1 Setting the language ........................................................................................................................................... 42
6.2.2 Setting date and time .......................................................................................................................................... 42
6.2.3 Setting further parameters................................................................................................................................... 43
6.3 Function tests .................................................................................................................................... 44
6.3.1 Checking control functions .................................................................................................................................. 45
6.3.2 Checking additional functions.............................................................................................................................. 46
6.3.3 Checking parallel operation................................................................................................................................. 49
7Functions and settings..................................................................................................... 54
7.1 Key lock ............................................................................................................................................. 54
7.2 General.............................................................................................................................................. 54
7.2.1 Setting device ID ................................................................................................................................................. 54
7.2.2 Setting the baud rate ........................................................................................................................................... 55
7.2.3 Setting the voltage display kV/V.......................................................................................................................... 55
7.2.4 Setting current display unit .................................................................................................................................. 56
7.2.5 Setting the switching pulse time .......................................................................................................................... 56
7.2.6 Configuring control inputs IO1-X1:33/31 ............................................................................................................. 58
7.2.7 Configuring output relays IO1-X1:25/26 and IO1-X1:23/24 ................................................................................ 59
7.2.8 Dimming display .................................................................................................................................................. 60
7.2.9 Setting motor runtime monitoring ........................................................................................................................ 61
7.2.10 Swapping tapping direction ................................................................................................................................. 63
7.3 NORMset........................................................................................................................................... 63

Table of contents
Maschinenfabrik Reinhausen 2014 52489566/01 EN TAPCON® 260
7.4 Control parameters............................................................................................................................ 65
7.4.1 Setting desired value 1...3................................................................................................................................... 67
7.4.2 Bandwidth............................................................................................................................................................ 68
7.4.3 Setting delay time T1........................................................................................................................................... 70
7.4.4 Setting control response T1 ................................................................................................................................ 70
7.4.5 Setting delay time T2........................................................................................................................................... 71
7.4.6 Adjustment of desired voltage value dependent on active power ....................................................................... 72
7.5 Limit values........................................................................................................................................ 78
7.5.1 Activating/deactivating absolute or relative limit values ...................................................................................... 78
7.5.2 Setting undervoltage monitoring V< .................................................................................................................... 79
7.5.3 Setting overvoltage monitoring V> ...................................................................................................................... 82
7.5.4 Setting overcurrent monitoring I> ........................................................................................................................ 84
7.5.5 Activating/deactivating function monitoring ......................................................................................................... 85
7.5.6 Switching interval monitoring............................................................................................................................... 85
7.5.7 Permitted tap positions........................................................................................................................................ 87
7.6 Compensation ................................................................................................................................... 88
7.6.1 R&X compensation.............................................................................................................................................. 89
7.6.2 Z compensation................................................................................................................................................... 91
7.7 Cross-monitoring ............................................................................................................................... 93
7.7.1 Setting desired value for regulator 2 ................................................................................................................... 94
7.7.2 Setting undervoltage limit value V< for regulator 2.............................................................................................. 94
7.7.3 Setting overvoltage limit value V> for regulator 2................................................................................................ 95
7.7.4 Setting delay time for error message .................................................................................................................. 96
7.7.5 Setting transformer for regulator 2 ...................................................................................................................... 97
7.8 Transformer data ............................................................................................................................... 98
7.8.1 Setting the primary transformer voltage .............................................................................................................. 98
7.8.2 Setting the secondary transformer voltage.......................................................................................................... 99
7.8.3 Setting primary transformer current..................................................................................................................... 99
7.8.4 Setting the current transformer connection ....................................................................................................... 100
7.8.5 Setting the phase difference for the current transformer/voltage transformer................................................... 101
7.9 Parallel operation............................................................................................................................. 104
7.9.1 Assigning CAN bus address.............................................................................................................................. 105
7.9.2 Selecting parallel operation method .................................................................................................................. 105
7.9.3 Selecting parallel operation control ................................................................................................................... 108
7.9.4 Setting delay time for parallel operation error messages .................................................................................. 109
7.9.5 Deactivating parallel operation .......................................................................................................................... 109