95687687-OTIS-GEN2-Za-Programming-Tool

Telechargé par tattiouin
OTIS
Central & East Europe Area
FOD BERLIN
FIELD COMPONENT MANUAL
Service Tool Manual
MCB
G
e
N2
Part: 4 - AA3
No.: GCA26800H2IVa_FC1
Vintage: 01 / 1
Page: 1 / 34
Date: 5-Jul-2000
MCB – G
e
N2
Service Tool Manual
Copyright 2000, OTIS GmbH & Co. OHG Berlin. No part of this document may be copied or reproduced in
any form or by any means without the prior written consent of OTIS GmbH.
Authorization Date D1: 03-Mar-2000
Running on PCB: GCA 26800 H2
Software Version: GAA 30582 AAB
Document Revision :
Date Author Page Comment
04-Jul-2000 G. Priebe 1 - 33 Original Document
OTIS
Central & East Europe Area
FOD BERLIN
FIELD COMPONENT MANUAL
Service Tool Manual
MCB
G
e
N2
Part: 4 - AA3
No.: GCA26800H2IVa_FC1
Vintage: 01 / 1
Page: 2 / 34
Date: 5-Jul-2000
Table of Contents
1 Service Tool Description.............................................................................3
1.1 MCB Flow chart ........................................................................................................ 3
1.2 Service Tool Display.................................................................................................. 4
2 Short notations...........................................................................................15
2.1 Short Notations State (M – 1 – 1) ............................................................................ 15
2.1.1 Motion Command Modes............................................................................... 15
2.1.2 Table of Motion Commands (V1 - V4) for MCS220....................................... 16
2.1.3 Motion Logic State.........................................................................................16
2.1.4 INPUT (M – 1 – 2).........................................................................................16
2.1.5 OUTPUT (M – 1 – 3).....................................................................................17
2.1.6 VCB – Status (M – 1 – 5)............................................................................... 17
2.2 Short notations Digital / Analog Converter (M – 2 –1)........................................... 18
2.3 Test / Event logging (M – 2 – 2).............................................................................. 18
2.3.1 SYS System and MCB related Messages .................................................... 19
2.3.2 INV Inverter related Messages...................................................................... 21
2.3.3 ALW Analog Load Weighing related Messages.......................................... 22
2.3.4 MC Information about Motion Commands.....................................................23
2.3.5 MLS Motion Logic State related Messages.................................................. 25
2.3.6 DRV Drive control related Messages........................................................... 27
2.3.7 Learn run related Messages.......................................................................... 28
2.4 Short notations DATALOG (M – 2 – 5)................................................................... 29
2.5 SETUP error handling (M – 3) ................................................................................ 30
2.6 Parameters .............................................................................................................. 30
2.6.1 Contract (M – 3 – 1) ...................................................................................... 30
2.6.2 Profile Parameters (M – 3 – 2)......................................................................31
2.6.3 Vane parameters (M – 3 – 3)........................................................................ 32
2.6.4 Start - Stop Parameters (StaSto) (M – 3 – 4) ............................................... 32
2.6.5 ENG VCB Parameters (ENG) (M – 3 – 5) ....................................................33
2.6.5.1 Motor Parameters (M – 3 – 5 – 1) .................................................................33
2.6.5.2 Control Parameters (M – 3 – 5 – 2)...............................................................33
2.6.5.3 MotEqC Parameters (M – 3 – 5 – 3).............................................................. 33
OTIS
Central & East Europe Area
FOD BERLIN
FIELD COMPONENT MANUAL
Service Tool Manual
MCB
G
e
N2
Part: 4 - AA3
No.: GCA26800H2IVa_FC1
Vintage: 01 / 1
Page: 3 / 34
Date: 5-Jul-2000
1 Service Tool Description
1.1 MCB Flow chart
MCB II Menu >
Setup = 3 Calibr = 4
MCB II - Menu >
Monitor = 1 Test =
2
State = 1 Input = 2
Output = 3 VCB = 5 DAC =1 ErrLog = 2
Self = 3 Part = 4 > Contrac = 1Prof = 2
Van = 3 StaSto = 4 > Learn = 1 EncAdj = 2
LoadW = 3
MCB-SW: 14-JAN-00
GAA30582AAA
DataLog = 5 PVT = 6
Fan = 7 Maint = 8 > Eng = 5 Default =6
Store = 7 Load = 8
Status = 1 Set = 2
Actual = 1 Saved = 2
OVFWW(405N) w.VCB
9kW / 480V / 25A
<M>
Monitor = 1 Test = 2
<2>
<4>
VCB-SW: 14-JAN-00
GAA30583AAA
Protocol version
MCB: 22 VCB: 22
Note: the suffix ”w. VCB” is always displayed to
indicate that the software installed in this pack-
age requires the VCB board
Safety = 9 LoadW = A
RopeSlip = B >
Calib. = 4 Setup = 3
LWB-SW:
GAA30339AAA
When communication to VCB is down, a string
of asterisks (”****”) will be displayed instead of
the expected string.
When communication to LWB and /or
VCB is down, a string of asterisks (”****”)
will be displayed instead of the expected
I_chk = 1 RDYchk
= 2
BSWdi 3
<9>
<8>
OTIS
Central & East Europe Area
FOD BERLIN
FIELD COMPONENT MANUAL
Service Tool Manual
MCB
G
e
N2
Part: 4 - AA3
No.: GCA26800H2IVa_FC1
Vintage: 01 / 1
Page: 4 / 34
Date: 5-Jul-2000
1.2 Service Tool Display
Monitor = 1
State = 1 This display is used to observe the system state.
State = 1 Input = 2 NORMAL IDLE 00
Output = 3 VCB = 5 <1> DRV: Rollb Start
for the characters:
NORMAL* = Motion Command Mode
IDLE* = Motion Logic State
00* = floor counter
The bottom landing is always number 0.
DRV: Rollb Start* = Actual Event Display
* Explanation of the short notations, see point
2. Short notations.
Monitor = 1
Input = 2, Output = 3 This display is used to watch the state (high or low)
of the input or output values.
State = 1 Input = 2 NORMAL IDLE
Output = 3 <2> UIB DIB <WT>
NORMAL IDLE
<3> DR up dn by
for the characters (example):
NORMAL* = Motion Command Mode
IDLE* = Motion Logic State
UIB DIB <WT>* = Inputs
DR up dn by* = Outputs
Note
:
capital letters = input/output is active.
With < GO ON > further inputs/outputs can be displayed.
It is possible to fade-in current event messages on display.
Activate this feature <Shift> <1> or <ON>.
Deactivate it by pressing <Shift > < 0> or <OFF>.
* Explanation of the short notation, see point
2. Short notations.
OTIS
Central & East Europe Area
FOD BERLIN
FIELD COMPONENT MANUAL
Service Tool Manual
MCB
G
e
N2
Part: 4 - AA3
No.: GCA26800H2IVa_FC1
Vintage: 01 / 1
Page: 5 / 34
Date: 5-Jul-2000
Monitor = 1
State = 5
1.line: MCB state display
2.line: VCB state display
Left column: VCB supervisor state
Shut Shut down
RDY Ready for run
RUN Run (see run substate)
* * * * VCB not present / no communication
Right column: VCB run - substate
IDLE Idle, PWM off, all controller switched off
PMAG Premagnetisation, PWM active, Speed control with reference value 0
LOOP Closed-Loop control, PWM and all controllers active
DMAG Demagnetisation
* * * * VCB not present / no communication
Test = 2
DAC = 1 Analog output channel for the system variables
DAC = 1 Errlog = 2 PROFILE GENERATR
Output = 3 Part = 4 <1> = 950 [0.1% fn]
for the characters:
PROFILE GENERATR*= selected variable
950 = actual value of selected variable
[0.1% fn] = Unit of the actual value
Use <GO ON> and <GO BACK> to scroll to the values.
Explanation of the Short notations see point
2. Short notations.
RUN_UP CONST
VCB: RUN LOOP
1 / 34 100%
La catégorie de ce document est-elle correcte?
Merci pour votre participation!

Faire une suggestion

Avez-vous trouvé des erreurs dans linterface ou les textes ? Ou savez-vous comment améliorer linterface utilisateur de StudyLib ? Nhésitez pas à envoyer vos suggestions. Cest très important pour nous !