yas meme

1
YASKAWA Electric Corporation
MEMOBUS Ethernet
Driver
1 System Configuration.......................................................................................................3
2 Selection of External Device............................................................................................5
3 Example of Communication Setting.................................................................................6
4 Setup Items....................................................................................................................38
5 Supported Device...........................................................................................................42
6 Device Code and Address Code....................................................................................44
7 Error Messages..............................................................................................................45

MEMOBUS Ethernet Driver
GP-Pro EX Device/PLC Connection Manual 2
Introduction
This manual describes how to connect the Display and the External Device (target PLC).
In this manual, the connection procedure will be described by following the below sections:
1System Configuration
This section shows the types of External
Devices which can be connected and SIO
type.
)"1 System Configuration" (page 3)
2Selection of External Device
Select a model (series) of the External
Device to be connected and connection
method.
)"2 Selection of External Device" (page 5)
3Example of Communication Settings
This section shows setting examples for
communicating between the Display and
the External Device.
)"3 Example of Communication Setting" (page
6)
4Setup Items
This section describes communication
setup items on the Display.
Set communication settings of the Display
with GP-Pro EX or in offline mode.
)"4 Setup Items" (page 38)
Operation

MEMOBUS Ethernet Driver
GP-Pro EX Device/PLC Connection Manual 3
1 System Configuration
The system configuration in the case when the External Device of YASUKAWA Electric Corporation and the
Display are connected is shown.
Series CPU Link I/F Interface Setting Example
MP900 MP920 Ethernet port on 218IF-01
(10BASE-5)
Ethernet (TCP) Setting Example 1
(page 6)
Ethernet (UDP) Setting Example 2
(page 10)
MP2000
MP2300
MP2200
Ethernet port on 218IF-01
Ethernet (TCP) Setting Example 3
(page 14)
Ethernet (UDP) Setting Example 4
(page 18)
Ethernet port on 218IF-02
Ethernet (TCP) Setting Example 7
(page 30)
Ethernet (UDP) Setting Example 8
(page 34)
MP2310
MP2300S
Ethernet connector on CPU unit
Ethernet (TCP) Setting Example 5
(page 22)
Ethernet (UDP) Setting Example 6
(page 26)
Ethernet port on 218IF-01
Ethernet (TCP) Setting Example 3
(page 14)
Ethernet (UDP) Setting Example 4
(page 18)
Ethernet port on 218IF-02
Ethernet (TCP) Setting Example 7
(page 30)
Ethernet (UDP) Setting Example 8
(page 34)
MP2400 Ethernet connector on CPU unit
Ethernet (TCP) Setting Example 5
(page 22)
Ethernet (UDP) Setting Example 6
(page 26)
• This driver does not support GP-4100 series and GP-4*01TM.

MEMOBUS Ethernet Driver
GP-Pro EX Device/PLC Connection Manual 4
Connection Configuration
• 1:1 Connection
• 1:n Connection
*1 The maximum 32 External Devices connection by UDP connection, the maximum 16 External Devices
connection by TCP connection.
• n:1 Connection
*2 When Ethernet port on CPU unit in MP2310/MP2300S/MP2400 is used, up to 4 Displays can be
connected.
Display
HUB
External Device
MP920: 10BASE-5
MP2000: 10BASE-T
Display External Device
HUB
MP920: 10BASE-5
MP2000: 10BASE-T
External Device
The max number of External Device : n *1
Display
HUB
External Device
MP920: 10BASE-5
MP2000: 10BASE-T
Display
The max number of Display : 10*2

MEMOBUS Ethernet Driver
GP-Pro EX Device/PLC Connection Manual 5
2 Selection of External Device
Select the External Device to be connected to the Display.
Setup Items Setup Description
Maker Select the maker of the External Device to be connected. Select "YASKAWA Electric
Corporation".
Driver
Select a model (series) of the External Device to be connected and connection method.
Select "MEMOBUS Ethernet".
Check the External Device which can be connected in "MEMOBUS Ethernet" in system
configuration.
)"1 System Configuration" (page 3)
Use System Area
Check this option to synchronize the system data area of the Display and the device
(memory) of the External Device. When synchronized, you can use the External Device’s
ladder program to switch the display or display the window on the Display.
Cf. GP-Pro EX Reference Manual "LS Area (Direct Access Method Area)"
This feature can also be set in GP-Pro EX or in the Display's offline mode.
Cf. GP-Pro EX Reference Manual "Display Unit (System Area) Settings Guide"
Cf. Maintenance/Troubleshooting Guide "Main Unit - System Area Settings"
Port Select the Display port to be connected to the External Device.